Updated at: 17-04-2022 - By: micdot

An easy guide on how to reset the airbag light on a VW without a tool is what I’m going to talk about in this post. I will talk about some of these things in this article.

Maybe you are interested:

This means that when your airbag tells you there is a problem, the module will be lit up. read more about Mazda 6 airbag light flashing what is the cause here

You Are Watching: Guide On Vw Airbag Light Reset Without The Tool Updated 04/2024

Take off the battery terminals on the battery of some older cars to reset the airbag light. You can do this without a scanner or any other tool by doing this: Even so, make sure that the SRS warning light isn’t still on.

It’s important to keep in mind that when the airbag light comes on, this means there’s a problem with the airbag system.

Sometimes, a broken airbag, broken wires, or bad connections could be to blame. Sometimes, a faulty control unit could be to blame.

Make sure you always check the SRS system, even if you haven’t been in an accident recently. You can change it even if you haven’t been hurt.

You should check the airbag system every 8 to 10 years because it has a lot of wires and sensors.

However, this doesn’t mean that you have to change the whole system. It’s important to check them out from time to time to make sure that everything is working as it should be.

What Does Service Airbag System Mean?

If your car has a driver information center (DIC), you might see a message about your service airbag system there, too.

However, if there is a problem with the airbag system that needs to be fixed, the service airbag system message will only show up.

Even though this problem can be small or mean a big problem has happened.

This could be telling you that your airbags won’t work if there’s an accident. When this happens, you’ve lost your airbag protection, which means that you might get hurt in an accident.

There is a need to act quickly if you see that the service airbag system message is on. Make sure it is fixed right away.

You might also see the SRS airbag light go on when the service airbag system message comes on.

A car crash can make its crash sensors go off even if the airbags haven’t been deployed.

This is why you should always check your car to make sure this doesn’t happen.

There are ways to deal with both the service airbag system message and the SRS airbag light coming on.

Getting new SRS airbag modules is the first thing to do.

If you know a lot about how to fix cars, you can reset the unit on your own.

It’s possible that you’ll like my YouTube videos, too. Please join me on YouTube by subscribing here, so you can see my new videos when I post them.

You can, however, ask a repair shop for help if you’re sure you can handle it or don’t want to spend money on tools and software.

How Do You Reset The Airbag Light On A VW?

Is the airbag light from your car coming on in your car’s dashboard? Interested in how to do it?

A few of the dashboard lights you need to pay attention to are your airbag lights and the engine. This airbag warning light is especially important because it can save your life.

Airbags are meant to inflate when there is a collision, but when the light is on, this won’t happen. This is important to remember.

With a scanner, you need to do these things:

It’s the first step.

Put the car key in the ignition system, and then turn your car switch to the on position to start the car up and run.

Step two:

After that, look at the airbag light going on. Keep in mind that the light will stay on for about seven seconds before it goes out.

After shutting off, make sure to turn off the switch right away and then wait three seconds before you turn it back on.

Step three:

There are two more times you can do steps 1 and 2.

After that, you can start your engine. Then you can drive. Once everything is done, the SRS light will be on for about seven seconds before going off again. This has now been done, and your airbag light has been turned off.

How Do You Reset The Airbag Light On A VW Beetle?

People who buy a Volkswagen Beetle will find that it has traction control, ABS brakes, front and side airbags, and a lot of other safety features.

This means that when your airbag module lights up because it has found a problem, you will know that something is wrong with it.

You can use the VAG service and the airbag reset tool to reset the airbag light on a VW Beetle. You can buy the airbag reset tool at any auto parts store near you.

It’s the first step.

Turn off the engine. Put the airbag reset tool and the VAG service into your Beetle’s diagnostic port, which is on the hood release latch. Then, turn on the hood.

Step two:

Now, press the select button on the reset tool until the yellow and red lights come on.

Step three:

After that, turn on the ignition, but don’t start the car at this point.

It’s time to press the tool’s “Enter” button for about 10 seconds until the lights come on. In this case, stop the engine.

Guide On, VW Airbag Light Reset Without the Tool

If you want to reset the airbag light in most cars, you’ll need to use a scanner.

Though this is for your own safety, you should always fix the problem when the airbag light comes on.

There are some car models that let you reset the airbag light without having to use a scanner. You can do this by taking the battery terminals off the car.

Under the passenger or driver seat, look at the wiring system. If there is corrosion or missing wires in the connector plug, you need to fix it.

You can just spray the connector plugs with an electronic cleaner and then start your car again, and it will work.

What Happens If You Disconnect Airbag Sensor

Take care not to remove the airbag system unit from the harness unless you’ve unplugged the battery. This might cause the airbags to deploy right away, which could damage your car’s computer system.

However, after you disconnect the positive battery cable, make sure to wait about three minutes before you remove the computer module from the battery.