Updated at: 04-03-2022 - By: micdot

Using the right tools is critical when it comes to putting together an automobile. The installation of a certain component may be difficult or impossible without the use of special tools. When it comes to installing anything at all, you may not be able to. The same holds true for the installation of a power steering pulley. What may be the reason for your skepticism?

With no tools, how do you put in a power steering pulley? You’ll need penetrating oil, a hammer, and a socket if you wish to install a power steering pulley without a tool. This method can harm the pulley if you aren’t careful, so use extreme caution. When it comes to purchasing or borrowing a tool, you should always do so. Power steering pulley installation is rather straightforward with the correct tools. There are times when these tools aren’t available, so you may prefer to go without them. Even still, getting the tools is recommended because installing without them might be dangerous and prone to problems. However, if you’re still interested, these are the actions you need to take.

You’ll learn how to install a power steering pulley without the need of any tools in this post. Here, you don’t need any tools to do the task. With the proper training, you may be able to decrease the potential for harm. Is there anything else we need to know before we get started?

Can You Install Power Steering Pulley Without Tool?

You don’t need special equipment to put in a power steering pulley. However, it’s a difficult process that comes with a lot of risks.

It’s not difficult to install power steering pulleys when you have the proper tools. Even so, you can’t run it like a breeze if you don’t have any tools to work with. Alternate tools, for example, can damage or even bend your pulley, rendering it inoperable. Because of this, you should proceed at your own pace.

How Do You Install Power Steering Pulley Without Tool?

Following these steps will allow you to install a power steering pulley without the need of a tool Lubricate the shaft and pulley. Pulleys and steering pump shafts should be lubricated before anything else is done. Penetrating oil would be the ideal lubricant. Oil with low viscosity is often known as penetrating fluid.

Using this oil can help you remove rusted pieces. As a result, a power steering pulley is an excellent addition.

Keep the pump on the floor.

As a last step, you’ll hold the pump in place while keeping the pulley on top of its shaft in place.

Hammer the pulley lightly.

Hammer the pulley to get it aligned and running smoothly. Avoid harming the pulley by being gentle with yourself when handling it.

Assist the shaft with a socket.

The shaft should gently slide in the pulley after a few hammer blows. Another hammer, socket, or shaft will be needed for this. As a result, the damage will be minimized and the stress will be reduced.

Hold the pump against the ground.

Make sure the pump is firmly pressed on the ground as you pound the shaft! The goal is to dissipate the shock force into the ground while simultaneously strengthening the casing.

Keeping your foot firmly planted on the floor and moving gently is critical here, as you run the risk of smashing the pump shaft through the rear of the housing.

As a visual help, this video clip shows how to install a power steering pulley without the need of a tool.

Can You Put a Pulley on With a Hammer?

With a hammer, you may attach a pulley. However, if you do it that way, it will be less effective.

When you hammer down the pulley, you only need a minimal amount of force. If the pounding continues, the pulley may flex and get damaged, rendering it useless.

Instead of a hammer, you can use a screw, some nuts, and another screw to complete the installation.

Screw in the nuts and washers first, then attach the pulley to the sprocket. Next, screw and bolt the pump shaft with the nut, screw, and washers you just installed.

To secure the pulley to the pump, grab the pulley and turn the nut clockwise. Next, loosen the pulley’s grip on the crankshaft until it is parallel to it.

What Is the Best Tool to Install Power Steering Pulley?

Installing a power steering pulley requires the use of the appropriate tool. Here are a few suggestions:

OEMTOOLS 27031 Power Steering Pulley Puller

This power steering pulley puller is perfect for both professional and DIY mechanics. As a result of its durability and ease of use, it is an ideal pulley remover for retail settings. Two thorough pulley removal guidelines and a carrying case are also included in the tool package.

This part is designed to fit the majority of power steering pulleys on the market today. GM, VW, Chrysler, Ford, and Chrysler/Plymouth power steering pulleys are all compatible with its two screws. Removal of hubs with diameters ranging from 1-3/8 inch to 1-14 inch is simple. It also removes GM V6 engine water pump pulleys and vacuum pump pulleys using this equipment.

To replace and adjust pulleys, you can utilize it. Rugged steel is used for the pulley clips and removal bolts, so they can withstand even the smallest amount of pulling force. The high standards and quality used in the construction of this power steering pulley puller ensure that it will endure a long time.

OTC 4531 Harmonic Balancer Puller and Installer Set

Pulleys and press-fit motors for power steering pumps can be removed and installed with a reversing 2-in-1 tool. This OTC pulley puller can also be used to install and remove other press-fit pulleys with hub diameters of 28mm, 32mm, 34mm, or 35mm.

It is convenient to store the OTC power steering pulley puller because it comes with a container made of durable plastic. It has also been updated to incorporate a wider range of brand adapters, making this kit even more versatile.

GEARWRENCH 41560D Power Steering Pump Puller Set

Install and remove power steering pump pulleys on practically all local cars with this third item’s high-quality toolset. Connectors for a wide range of automobiles are included in this removal kit.

The kit can be used with a variety of different-sized hubs. Fast disconnecting tools for pickups weighing 12, 34, and 1 ton are also included in this puller.

Additional tools include a 3893 disconnection device, a 41562 bushing with a screw set, and a 41561 bushing with a screw set. A rip container is included with each of these goods for easy storage and preservation.

Lisle 39000 Pulley Puller

The power steering pulley may be easily replaced with the use of a unique pulley puller. V-shaped and serpentine belt pulleys will both benefit from this pulley.

It’s a lot faster than other pullers of the same type. Therefore, it is compatible with the vast majority of home appliances.

The pulley shaft is completely protected by a sturdy casing on this sort of puller. Pulleys with large and small teeth as well as long and short pulley shafts as well as four installation connectors are included.

You should lubricate or oil the pressure points and screws before using them to get the best results.
OTC Tools 4530 Power Steering Pulley Service Set

OTC’s mechanical equipment production is widely known and respected. You’ll get everything you need in this Power Steering Pulley Puller Kit to install and repair the power steering pump pulleys on any local vehicle. There are few pulley-pullers on the market that are as good as this one.


In a nutshell, you don’t need any special tools to put in a power steering pulley. The problem is that it’s extremely difficult to implement and has many risks attached to it. Hammers can also be used to install power steering pulleys as an alternative method of installation. Even with a little force, it’s possible to ruin your pulley. As a result, it’s still advisable to buy or borrow the tool.

Even without tools, you can save money. However, if you aren’t experienced with this type of work, it is preferable to avoid the risks and purchase the proper gear to ensure your success. With the right tools, you can ensure a sound installation that is both fast and efficient.